-
product
High Range Chemiluminescence NOX-NO2-NO Analyzer
Model N200H
Teledyne Advanced Pollution Instrumentation
The Model N200H uses the proven chemiluminescence detection principle, combined with a state-of-the-art modular architecture, and intuitive operating software to provide accurate and dependable measurements of high-level Nitric Oxide (NO), Nitrogen Dioxide (NO2) and total Nitrogen Oxides (NOx) gases for use in extractive type CEM systems.
-
product
OPTICAL PHASE NOISE TEST AND MEASUREMENT SYSTEM
OEwaves’ HI-Q® Optical Test Measurement System utilizes a homodyne methodology for automated measurement capable of testing ultra-low phase noise laser sources. The user friendly test system is capable of rapidly measuring laser phase noise and estimating its FWHM linewidth down to < 3 Hz without complex setup or reference lasers normally required to make such a narrow linewidth measurement.
-
product
Test Contactor/Probe Head
cBoa
cBoa™ test contactors and probe heads are the solutions for contacting high-frequency devices for package test or final test at wafer. The robust design and materials of the cBoa probe withstand the rigors of high-volume test by providing longer life and higher yield. The homogeneous DUT side plunger provides longer run times between cleaning and increased probe life.The cBoa features a stainless-steel spring for tri-temp testing and performs in operating temperatures of -55°C to +155°C and bandwidth of up to 35 GHz @ -1 dB.
-
product
Fibre Channel Test & Simulation Interface for PCI Express
PCIe-FC4
Avionics Interface Technologies
Half-size four lane PCIe board - Supports Point-to-Point, Switched Fabric, and Arbitrated Loop topologies - Two independent Fibre Channel ports - Two SFP sockets accept fiber or copper transceivers - Each port supports 1, 2, and 4 Gbps speedsComprehensive decoding of FC-1, FC-2, and Upper Layer Protocol (ULP) frames - Full Error Injection and Detection - IRIG-B Time Code Encoder/Decoder for Data Correlation - In-line Port Configuration for Transparent Analyzer - Supports multiple ULPs including FC-AE-ASM, FC-AE-RDMA, FC-AE-1553, and FC-AV - Compatible with AIT’s fcXplorer GUI Bus Analyzer Software
-
product
In-Circuit Test
TR5001T
The TR5001T Tiny 2 ICT is a new full feature In-Circuit board tester with a laptop sized footprint that provides a very cost effective alternative to large In-Circuit testers.
-
product
IEC60068-2-75 Spring Hammer Test
CX-T03
Shenzhen Chuangxin Instruments Co., Ltd.
*Impact hammers are used to check the durability of enclosures for electrical appliances of other electronic products.If damage occurs from the Impact Hammer test .Accessibility probes can be used to measure the extent or severity of the damage.The Impact Hammer simulates the mechanical impact to which electrical equipment may be subjected. *This hammer is mainly used to test household and similar electrical appliances shell, lever, handle, knobs, lights and other shell to withstand mechanical shocks.* The impact tester made of stainless steel or alloy.
-
product
Variable Frequency AC Resonant Test System
HDXZ-270kVA/270kV
HD Power Test Equipment Co.ltd
HDXZ-270kVA/270kV Variable Frequency AC Resonant Test System is applied for AC dielectric test for electric equipment.1. 10kV/300mm2 cable 3km AC withstand test,capacitance≤1.1265uF,test frequency:30-300Hz, test voltage 22kV, test time 5min;2. 35kV/300mm2 cable 1km AC withstand test,capacitance≤0.1945uF,test frequency:30-300Hz, test voltage 52kV, test time 60min;3. 110kV/630mm2 cable 0.2km AC withstand test,capacitance≤0.0368uF,test frequency:30-300Hz, test voltage 128kV, test time 60min;4. ...show more -
product
Offline In-Circuit Test Solutions
TestStation’s offline test systems are designed for a human operator or collaborative robot for product handling. TestStation systems scale to support from 128 to 15,000 test points. Our newest Multi-Site systems double productivity per system, reducing Capex and Opex for manufacturers.
-
product
C++ Test Framwork
Google Test
a unit testing library for the C++ programming language, based on the xUnit architecture. It can be compiled for a variety of POSIX and Windows platforms, allowing unit-testing of C sources as well as C++ with minimal source modification.
-
product
LT-500A Aging-Life Test System For LED Luminaires
Hangzhou Everfine Photo-E-Info Co., LTD
LT-500A system is widely used for normal /accelerated aging, lumen maintenance measuring, chromaticity shift measuring, lifetime evaluation and temperature characteristic testing for LED luminaires, arrays, and modules. The extrapolation of lifetime by programmable models is also available to estimate the lifetime of LED luminaires.
-
product
Short Range Detection Systems
The EFM-100 kit comes complete with a high accuracy short range detector, inverted mounting hardware, cables and adapters. It is designed to provide a real time reading of the electrical field in the atmosphere with a time vs e-field graph displayed on a computer along with lightning strike distances accurate to within one mile.
-
product
Parametric Test Solutions
Reduce your cost-of-test up to 20% with our ultra-fast CPU Overcome your process test challenges Boost measurement throughput and lower costs with our synchronous/asynchronous parallel test capability Better low-level measurement performance Create customized waveforms Reduce transition costs
-
product
Pocket Size Digital Multimeter, Resistance Measure, 3999 Count, Average, Auto Range, 3.75 Digit
72-10395
Pocket sized multimeter which comes in a self-contained folding case. The meter measures AC/DC voltage, resistance, capacitance & frequency.
-
product
Explosive Atmosphere Test
This test demonstrates that a part will not ignite while operating in an explosive ambient atmosphere. The tests are conducted at ground level pressure as well as reduced barometric pressures, in a closed explosion-proof chamber.
-
product
PORTABLE OIL TEST
PORTABLE OIL TEST. Test voltage rises up with 3 different speeds. Interchangeable oil cups sit in cradle contacts inside a test chamber with safety high-voltage interlock and hinged grounded metal lid with 2 windows to see the arc across the probes.
-
product
Hipot Tests
The hipot test (high potential test) or dielectric withstand test, is used to determine the insulation and dielectric strength. It is carried out on modules, devices and systems of protection class I + II. In this test, the insulation of the test object is subjected to greater stress by the high voltage than in normal operation. It is determined whether the insulation of all current-carrying conductors, as well as the safety distance to the enclosure, is sufficient and complies with the legal re...show more -
product
Intraocular Lens Optical Test System
OptiSpheric® IOL R&D
The OptiSpheric® IOL R&D is specially designed for the analysis of single intraocular lenses in research and development. With the OptiSpheric® IOL R&D, important parameters of all types of lenses (monofocal, multifocal, trifocal, toric, aspheric and those with extended depth of focus (EDOF) – whether diffractive, refractive or sectors) can be measured and tested in air or in situ in accordance with ISO 11979.
-
product
Real Car Transient Test System
RealCar Simulation Bench
This system is suitable for transient test of actual vehicle in combination with the real-time model calculation by the measurement/control panel and low inertial motor. By replacing the wheel of the actual vehicle with the tire type bearing, the axle shaft is taken out to the outside of the vehicle and connected to the low inertia motor. It can be reproduced the sliding motion which the chassis dynamometer cannot be realized. Also, since the longitudinal force is not occurred in the vehicle, the vehicle restraint can be simplified and the behavior such as shift shock can be reproduced on the bench.
-
product
Stimulus Test Cell
HA7300
The Stimulus Test Cell HA7300 is a test cell which provides an environment for high-speed, highly accurate temperature and pressure test of differential pressure sensors, utilizing Advantest’s unique temperature control unit with simultaneous temperature control for 8 devices, as well as a newly developed 2Port pressure controller and pressure application nozzle.
-
product
Low Noise Test Cables For N1413 With B2980 Series, 1.5 M
N1427A
The N1427A is designed to operate specifically with the B2985B/87B Electrometer/High Resistance Meter. It comes with a separate triaxial (special screw-type) female connector and a High Voltage BNC (special type) female connector. This allows terminal configuration to be converted to any other configuration. Therefore, custom test fixture can easily be constructed. The N1413A High Resistance Meter Fixture Adapter is also required to connect the N1427A to the B2985B/87B.
-
product
Functional test
Maschinenbau Haldenwang GmbH & Co. KG.
Test bench for small vehicles with 2 wheelsRoad load simulationDetermination of maximum speedMeasurement and evaluation of speed, speed, distance traveledDisplay of wheel power at test speedDisplay on your PC monitorExpression of test resultsCustomer and vehicle databaseEuro system console MCD 2000 with switching elements for roller setPort for external devices
-
product
Wireless Device Functional Test Reference Solution
The Keysight S8890A Wireless Device Functional Test Reference Solution provides an automation environment which is both simple to use, yet comprehensive and powerful. Based on the Test Automation Platform www.keysight.com/find/TAP, S8890A provides optional instrument driver/plug-ins offering simplified logically grouped control steps. These steps can be sequenced, looped and swept to provide powerful individual test cases or comprehensive sequences. Each driver/plug-in is provided with extensive starter sample test cases which can be modified by Keysight or the end user the UE to be tested. Plug-in options:
-
product
Meter test station
TS23
Calmet Smart Calibration Devices
Three phase reference standard of accuracy 0.02% (or 0.04%). It makes possible electricity meters testing on the site or in the laboratory up to 3x120A/600V
-
product
Automotive Test Lead Kit
143
Test Lead Kit includes our basic set of interchangeable specialty test probes designed for automotive use. The flexible back probing pins are great for sliding into automotive connectors like those on fuel injectors and MAP sensors. The large Crocodile Clips are good for clipping to grounds and battery terminals. Roll up storage pouch keeps your leads organized.
-
product
Socket Outlet Torque Test Device
CX-LJ
Shenzhen Chuangxin Instruments Co., Ltd.
For measuring and testing the torque strain exerted by appliances with plug pins on socket-outlets, in accordance with IEC 60065 clause 15.4.1 and figure 11, IEC 60335-1 clause 22.3, IEC 60884-1 clause 14.23.2.
-
product
DHCP Tests
The Dynamic Host Configuration Protocol (DHCP) provides configuration parameters to Internet hosts. DHCP consists of two components: a protocol for delivering host-specific configuration parameters from a DHCP server to a host and a mechanism for allocation of network addresses to hosts. DHCP is built on a client-server model, where designated DHCP server hosts allocate network addresses and deliver configuration parameters to dynamically configured hosts. (Source: RFC 2131)
-
product
Pneumatic Bump Test Machine
KRD20 series
The KRD20 series pneumatic bump test machine replaces the traditional mechanical cam-type crash bench and is suitable for repeated impacts on electronic components, equipment and other electrical and electronic products during transportation or working.
-
product
Shore Durometer Test Stand
UI-FT31
Shore Durometer Test Stand is used to support the durometer presser foot surface parallel to the sample support table to better complete the test.
-
product
Integrated Test Environment
ITE
The Integrated Test Environment (ITE) is our solution to handle complex hardware or software test projects.ITE provides features to define and manage requirements and test cases in different documents, link them with each other as well as plan tests and test campaigns. Moreover the tests can be developed, executed and evaluated by considering the linked requirements. Test results can additionally be recorded and finally reported in different, adaptable and configurable reports.
-
product
Low Resistance Test System
9100-2
Palico Instrument Laboratories
The Model 9100-2 measures the resistance of single or multiple battery separators quickly and accurately when used with our Model 9000-9100 Electrolyte Test Bath. This system uses a 4-terminal measurement technique which cancels the effects of electrode/electrolyte potentials.
